Rustler vxl invertido
Moderadores: Abib, gbatistela, mach, pixelman, Pimpolho
11 mensagens
• Página 1 de 1
Rustler vxl invertido
Iae galera,
Fui testar meu rustler vxl, e agora quando eu acelero para frente ele vai para tras o que sera ?
Fui testar meu rustler vxl, e agora quando eu acelero para frente ele vai para tras o que sera ?
Re: Rustler vxl invertido
Verifica se a regulagem do throttle no rádio não está no Reverse. Faça a configuração ESC/Rádio novamente, se precisar.
Elétricos (Nitro NEVER MORE) Variados Alguns LiPOs 2, 3, 4 e 5S Originais Originais Anywhere!! Just Fun!!! |
Re: Rustler vxl invertido
Como faço essa regulagem ?
E-revo 1/10 Manba Monster Original da e-revo TQ 2.4 lipos 4s(2 2s) 6s(2 3s) Original da e-revo Original da e-revo Pacaembu, Extra,Jacui,barueri |
Re: Rustler vxl invertido
Como vejo se a regulagem do throttle no rádio não está no Reverse ?
E-revo 1/10 Manba Monster Original da e-revo TQ 2.4 lipos 4s(2 2s) 6s(2 3s) Original da e-revo Original da e-revo Pacaembu, Extra,Jacui,barueri |
Re: Rustler vxl invertido
Opa. A questão da regulagem do "reverse" vc faz no próprio transmissor. Consulte o manual do rádio que explica isto. Quanto à calibragem transmissor/ESC, deves seguir as instruções no manual do ESC. Se ambos( ESC e Rádio forem Traxxas, no manual do carro existe essas instruções).
Elétricos (Nitro NEVER MORE) Variados Alguns LiPOs 2, 3, 4 e 5S Originais Originais Anywhere!! Just Fun!!! |
Re: Rustler vxl invertido
Inverta dois fios no motor
Aprenda a Pesquisar no RCMasters! <- Clique!
sucata de fios e imãs am rayovac amarelinhas raladas carecas slick onde der |
Re: Rustler vxl invertido
Voce pode me enviar um manual do rustler em portugues ?
E-revo 1/10 Manba Monster Original da e-revo TQ 2.4 lipos 4s(2 2s) 6s(2 3s) Original da e-revo Original da e-revo Pacaembu, Extra,Jacui,barueri |
Re: Rustler vxl invertido
Faça um Reset no transmissor. Assim:
"" The transmitter should be adjusted as follows:
If the transmitter setting have been adjusted, reset them to the factory defaults.
1. Turn transmitter off.
2. Hold both MENU and SET.
3. Turn transmitter on.
4. Release MENU and SET. The transmitter LED will blink red.
5. Press MENU once. The transmitter LED will blink red twice repeatedly.
6. Press SET to clear settings. The LED will turn solid green and the transmitter is
restored to default. """
Para Calibrar o ESC com o transmissor, faça o seguinte:
"" VXL-3s Setup Programming (Calibrating your ESC and transmitter)
Read through all of the programming steps before you begin. If you get lost
during programming or receive unexpected results, simply unplug the battery,
wait a few seconds, plug the battery back in, and start over.
1. Connect a fully charged battery pack to the VXL-3s.
2. Turn on the transmitter (with the throttle at neutral).
3. Press and hold the EZ-Set button (A). The LED will first turn
green and then red. Release the EZ-Set button.
4. When the LED blinks RED ONCE, pull the throttle
trigger to the full throttle position and hold it
there (B).
5. When the LED blinks RED TWICE, push the throttle
trigger to the full reverse and hold it there (C).
6. When the LED blinks GREEN ONCE, programming
is complete. The LED will then shine green or red
(depending on low-voltage detection setting)
indicating the VXL-3s is on and at neutral (D). """
"" The transmitter should be adjusted as follows:
If the transmitter setting have been adjusted, reset them to the factory defaults.
1. Turn transmitter off.
2. Hold both MENU and SET.
3. Turn transmitter on.
4. Release MENU and SET. The transmitter LED will blink red.
5. Press MENU once. The transmitter LED will blink red twice repeatedly.
6. Press SET to clear settings. The LED will turn solid green and the transmitter is
restored to default. """
Para Calibrar o ESC com o transmissor, faça o seguinte:
"" VXL-3s Setup Programming (Calibrating your ESC and transmitter)
Read through all of the programming steps before you begin. If you get lost
during programming or receive unexpected results, simply unplug the battery,
wait a few seconds, plug the battery back in, and start over.
1. Connect a fully charged battery pack to the VXL-3s.
2. Turn on the transmitter (with the throttle at neutral).
3. Press and hold the EZ-Set button (A). The LED will first turn
green and then red. Release the EZ-Set button.
4. When the LED blinks RED ONCE, pull the throttle
trigger to the full throttle position and hold it
there (B).
5. When the LED blinks RED TWICE, push the throttle
trigger to the full reverse and hold it there (C).
6. When the LED blinks GREEN ONCE, programming
is complete. The LED will then shine green or red
(depending on low-voltage detection setting)
indicating the VXL-3s is on and at neutral (D). """
Elétricos (Nitro NEVER MORE) Variados Alguns LiPOs 2, 3, 4 e 5S Originais Originais Anywhere!! Just Fun!!! |
Re: Rustler vxl invertido
Ok. Amanha vou testar isso, e falo se deu ou nao. Obrigado galera
E-revo 1/10 Manba Monster Original da e-revo TQ 2.4 lipos 4s(2 2s) 6s(2 3s) Original da e-revo Original da e-revo Pacaembu, Extra,Jacui,barueri |
Re: Rustler vxl invertido
Disponha.
Elétricos (Nitro NEVER MORE) Variados Alguns LiPOs 2, 3, 4 e 5S Originais Originais Anywhere!! Just Fun!!! |
Re: Rustler vxl invertido
Descobri: como comprei o rustler usado era os cabos invertidos do motor no esc.mas vou tentar fazer alguma coisa aqui porque ta tudo com fita isolantes.
E-revo 1/10 Manba Monster Original da e-revo TQ 2.4 lipos 4s(2 2s) 6s(2 3s) Original da e-revo Original da e-revo Pacaembu, Extra,Jacui,barueri |
11 mensagens
• Página 1 de 1
Quem está online
Usuários navegando neste fórum: Nenhum usuário registrado e 8 visitantes